13 Circuit Racing for sale

This MX5 1998 NB race car with hard top has been expertly prepared and has been proven to be a trouble free, reliable and a consistant performer. There is no evidence of accident damage. The car weighs approx 1000 kg and produces 108 kw at the rear wheels. Modifications and equipment include: CAMS approved BROWN DAVIS roll bar. RACING BEAT cold air intake and RACING BEAT exhaust headers. RACING BEAT tubular front sway bar with adjustable end links and RACING BEAT reinforced sway bar mounts. WHI

Completely rebuilt over the last period of Covid, ground up restoration, has not been on a track since rebuild. Fitted with a Nissan FJ 20 ET engine with forged internals and Motec management. Will need testing and sorting, just been dynoed at low boost to give the engine a bit of run time, comes with mounted wets and spare new fronts, a complete new forged engine in dismantled form, 3 engine blocks and 4 cylinder heads, and a mass of spares including 2 gearboxes. Was originally raced bu Keith L

MGB Group Sb top spec engine Quaife diff straight cut gearbox with overdrive Fully serviced ready to go nothing to spend , current seatbelt. $22.500 Message Stan for full specs 0416128867 .

Competed in the 2023 National Trans Am Championship and finished inside the top 10. Professionally maintained by Dream Racing Australia between each event. New front and rear brakes (Pads & Rotors) Motec Tps sensor upgrade, Soild plate clutch upgrade, Larger oil cooler upgrade, Air box upgrade, Tail shaft with upgraded yoke and new uni-joints, Rebuilt diff, Recently serviced gearbox, Spare Front Bar, Spare Sway bar, 8 Rims (4 x slicks & 4 x wets) Leak down test performed after last round

Motorsport Australia Historic log booked group N Mach 1 Mustang Rotisserie restoration taken back to metal, retaining its original exterior paintwork, not a showpony but presents very well. All new mechanicals inc Dry sump Dart based 351 Windsor forged internals RHS heads built by Kanaris Engines 600+ HP, Haltech ECU, New TKX close ratio, 9” 3.89 Trutrack, 4 link rear end on fully adjustable coil overs all round. Motorsport hubs front on 2-peice hub and rotors, tubular upper and lower wishbones

This immaculate C6 corvette is race ready with no expense spared. Some features include the following: Coil over suspension QA1 suspension Front splitter Rear carbon fiber wing Upgraded brakes 6 piston front and 4 piston in the rear Auto blip computer Quick release steering wheel Roll Cage Fuel Cell Haltech dash with new wiring approx $10,000 Light weight racing battery Isolators Polycarbonate front windscreen Polycarbonate rear windscreen Car has been completely guttered only weighs 1,200 ki

RX8 drift/track car project I have since given up on due to work commitments and a lack of time. I'd rather avoid parting it out. Includes: S1 RX8 chassis (stat write off, perfectly straight, no damage or rust that I've found). - cut out OEM driver seat mounting to fit race seat lower (havent patched hole yet). Custom shortened front uprights New LCAs New brake rotors New PMU pads New braided front lines New Custom valved coilovers New wheel bearings/hubs Wet NOS kit (10lb bottle) Other rando

Mazda in excellent condition, recent service, garaged, Mazda BP GTR Motor with factory Ihi ball bearing Turbo, 221 KW @ rear wheels s/5 gearbox, new h/d tailshaft triple plate tilton, alloy flywheel 4.11 detroit locker.S/4 breaks all round ht 10 pads new front koni struts, harness, autometer gauges intercooler spray 48’s. CAMS log book. ID plates and could be registered if changed to roadworthy.

Recent engine rebuilt with rolling road figures of 215bhp and a race weight minus driver of 880kg including 8 point roll cage, car is sold with Corbeau race seat and Luke 6 point harness already included. Car has a race built naturally aspirated Rover K Series 1.8