11 Motorsport Vehicles for sale

I am having to do a regretful sale of my beloved car. It is a near finished project dream car that I have been working on for the past 2 years. I bought it as a semi project car but was falsely advertised, so it became a big project that is nearly finished. I hope it goes to a caring car head or collector. The car is a classic car. No reg, no roadworthy incl. The KMs are approx. as I still use this car as my daily. INFO *JAPANESE IMPORT* 1993 Toyota Celica Convertible ST-183 3S-GE Engine Re

The GTR-X was a fascinating concept from the get-go; A fibreglass body, over a steel “ladder” chassis, which may seem exotic to an Australian market, but GM had been successfully using that technique with its iconic sports car, the Corvette, from 1953’s C1. Come 1969, the Corvette had evolved to the swoopy C3 guise, featuring independent suspension, four-wheel disc brakes and wild 427 L88 spec’ motors. Along that 16 year passage, the Corvette’s early mistakes became improvements and a smooth, fa

1980 vb sl/e commodore. 253 v8 automatic. Kept as original as possible. Always garaged barely driven. Has had brake system rebuilt and carby rebuilt a few years back. Has original purchase receipt also.

Up for sale is our Corolla KE70, aka Nana-Spec, project car 4A-GE motor (originally out of MR2) ECU and wiring is completed Motor runs (needs the return fuel line back to the tank to be plumbed up) Hydraulic clutch installed, needs to be bled Surge tank and pump installed New exhaust system Original paintwork and interior Minor rust in lower rear outer quarter panel and front edge of bonnet, and small amount of panel work required Clean chassis and underneath Selling due to not having enough

Project car regrettably up for sale 4AGE-ZE motor with LA3 mod plate Cast iron Celica 5-speed gearbox Shortened Hilux diff 15” Simmons wheels Front mounted intercooler behind bar Very clean underneath, no rust in chassis Interior mostly complete, missing a couple of mouldings in boot area Exterior in good condition, a couple of small rust spots, nothing major Motor not currently running Will require ECU and partial rewire Selling due to not having enough time - have had the car for 8 years

FOR SALE 2010 HOLDEN VE COMMODORE UTE SSV SET UP FOR STREET – TRACK CAR – DRAG RACE STREET REGISTERED WITH MOD PLATES QLD REGO 5-24 24500KM ENGINE 6.0 LITRE 495KW ON BACK WHEELS 1180 N.MT FORGE PISTONS ROD BOLTS CUSTOM CAM DOUBLE VALUE SPRING HARROP AIR INTAKE E85 INJECTORS E85 PUMP AND SURGE TANK 2300 HARROP SUPER CHARGER MANUAL 6 SPEED GTS S1 SEQUENTIAL SHIFTER CERAMIC CLUTCH WITH CUSTOM SLAVE CYLINDER 1000HP DRIVE SHAFT WITH 9” YOKE TRU TRACK DIFF CENTRE 4.11 GEARS 1000HP DRIVE SHAFT AXL

Statutory write off and fully repaired, We have photos of the damage which was the rear of the car,all receipts are available as well. Being a stat write off this vehicle can not be registered in Australia, can be used for track or export outside Australia. it is priced below our cost and needs to GO.

2012 Holden ve track ute cannot be registered. 5.7 LS1 vcm7 cam, ported heads, OTR cold air, trunuin upgrade, buckets, oil pump, timing chain, push rods, springs gaskets were all upgraded at same time was done about 1.5 year ago at KTMR performance. twin into single 3.5 exhaust sounds tuff,all braided oil lines, catch can, oil cooler, oil accumulator, powersteering cooler, coilovers, diff has a harrop full spool rated to handle 1000hp with 3.7 diff gears custom tailshaft (dount delete and bigg

CAMS LOG BOOKED NO RUST 4 DOOR TORANA BUILT IN MIND OF THE GROUP C A9X APART OF HAVING OVER 500 HP BUILT WITH ALL NEW PARTS GROUND UP. TESTED AT QUEENS LAND RACE WAY 30 LAPS AT 7,000 TO 7.5000 OIL PRESSURE STAYED AT 50PSI 60 TO 70 ON START UP,CAR STOPPED CORNERED DROVE FANTASTIC BRAKE PADS ARE PMU USED HAS CLUB REGO,BUT IS A FULL 100% RACE CAR 308 RACE ENGINE COME RACING BILLET 3.55 CRANK,H BEAM 1.125 RODS,WISCO .020 PISTONS,CLIVE ROLLER CAM,T-BAR CPMP PRO ROLLER LIFTERS,OIL GALLERY DELIVERY

PRICE REDUCED AGAIN! Calibra 117k 2.5 v6 man red this car would make a good hillclimber or trackday car has alcon 4p mono front calipers dba club spec t3 330mm rotors alcon advantage 320mm rear rotors 2p calipers arp wheel studs 5x120pcd eibach coils kyb eurospec shocks poly bushes front&rear 17/7 alloy wheels fed rsr 215/40/17&235/40/17 fed 595 rear. Have 3.2 v6 from 2004 vectra with cat cams pac v/springs arp head bolts new balancer mtec billet flywheel with arp studs crossram intake off 3.0l