11 Holden for sale

This left-hand-drive, GM Australia-built Holden Monaro is a real head-turner and the perfect car for the collector, professional racer or track day enthusiast – or the same person all wrapped up into one! The Monaro was assembled by GM Holden at Elizabeth in South Australia and is believed to be one of only a handful of left-hand-drive examples in the country. The odometer reads 31,739kms of which the vast majority (~31,000kms) were driven by Holden engineers at the Lang Lang proving ground in

The GTR-X was a fascinating concept from the get-go; A fibreglass body, over a steel “ladder” chassis, which may seem exotic to an Australian market, but GM had been successfully using that technique with its iconic sports car, the Corvette, from 1953’s C1. Come 1969, the Corvette had evolved to the swoopy C3 guise, featuring independent suspension, four-wheel disc brakes and wild 427 L88 spec’ motors. Along that 16 year passage, the Corvette’s early mistakes became improvements and a smooth, fa

2000 VX SS V8 with LS2 6.0lt Motor has just been built and has only done three sprint days at Sandown Raceway. Built by Octane Alley performance centre. Balanced engine Crow race cam kit Pepro stainless steal race valves INJ189 Injectors .020 shorter chrome molly push rods VCM sump with baffles and hinges Fully reconditioned cylinder heads Oversized Hypertech pistons Dual valve springs Engine was only bored to the first stage Engine was built for strength and reliability with power. Dyno tu

VU SS race/exhibition car project. Sold as rolling concern. Vehicle has a clean title and could be engineered and re registered with some work. Quick rundown *2001 VU SS *Statesman international front end conversion *4 inch reverse cowl *HSV Hard lid *HSV Sail Plain *New Blackout projector headlights *New Blackout Tail lights with LED *New Side Markers *Wilwood brake master *Wilwood brake bias valve *B&M line lock *Electric Power steering Conversion (fully functional for moving the car aroun

FOR SALE 2010 HOLDEN VE COMMODORE UTE SSV SET UP FOR STREET – TRACK CAR – DRAG RACE STREET REGISTERED WITH MOD PLATES QLD REGO 5-24 24500KM ENGINE 6.0 LITRE 495KW ON BACK WHEELS 1180 N.MT FORGE PISTONS ROD BOLTS CUSTOM CAM DOUBLE VALUE SPRING HARROP AIR INTAKE E85 INJECTORS E85 PUMP AND SURGE TANK 2300 HARROP SUPER CHARGER MANUAL 6 SPEED GTS S1 SEQUENTIAL SHIFTER CERAMIC CLUTCH WITH CUSTOM SLAVE CYLINDER 1000HP DRIVE SHAFT WITH 9” YOKE TRU TRACK DIFF CENTRE 4.11 GEARS 1000HP DRIVE SHAFT AXL

Sports sedan. Have to sell so I can finish other projects. Recently raced in NSW Hillclimb round on fresh set of A7 Hoosiers. This car has racing history and logbook dating back to 25/3/1982. 265 Hemi 6 mid-mounted. Genuine Hopwood wheels. Fully floating brakes, 10 bolt rear end and Ford single rail gearbox. Plenty of history in this car, and we can put you in contact with its original builder. Motor, genuine 48mm Webers, fuel system, and brakes have recently been re-done, and all electrics from

Statutory write off and fully repaired, We have photos of the damage which was the rear of the car,all receipts are available as well. Being a stat write off this vehicle can not be registered in Australia, can be used for track or export outside Australia. it is priced below our cost and needs to GO.

2012 Holden ve track ute cannot be registered. 5.7 LS1 vcm7 cam, ported heads, OTR cold air, trunuin upgrade, buckets, oil pump, timing chain, push rods, springs gaskets were all upgraded at same time was done about 1.5 year ago at KTMR performance. twin into single 3.5 exhaust sounds tuff,all braided oil lines, catch can, oil cooler, oil accumulator, powersteering cooler, coilovers, diff has a harrop full spool rated to handle 1000hp with 3.7 diff gears custom tailshaft (dount delete and bigg

PRICE REDUCED AGAIN! Calibra 117k 2.5 v6 man red this car would make a good hillclimber or trackday car has alcon 4p mono front calipers dba club spec t3 330mm rotors alcon advantage 320mm rear rotors 2p calipers arp wheel studs 5x120pcd eibach coils kyb eurospec shocks poly bushes front&rear 17/7 alloy wheels fed rsr 215/40/17&235/40/17 fed 595 rear. Have 3.2 v6 from 2004 vectra with cat cams pac v/springs arp head bolts new balancer mtec billet flywheel with arp studs crossram intake off 3.0l