11 items for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
All Results
10
Registered
Originally purchased in 2017 as a repairable writeoff with minimal damage to the front subframe. This C180K quickly had the full running gear removed and swapped with the CLK63. I have personally removed the complete rear axle including all suspension and driveline, complete front subframe including engine and gearbox. Stripped the entire vehicle to swap out the wiring harness to accommodate the M156 and 7G-Tronic transmission and dual fuel pump fuel system. I have installed the complete front e
6
Registered
Holden Torana sedan 1975 LS1 / T56 F.A.S.T. intake AFR cathedral port heads Comp Xtreme Energy cam 2000-7000 224/230, .581"/.588" lob sep 114 Comp cams hydraulic lifters Yella Terra true roller rockers Accel 40lb/hr fuel injectors Mal Wood Under dash Hydraulic clutch pedal assembly Mal Wood Reconditioned T56 and organic clutch B&M shifter Altra 9 A9 axles 28 spline Wilwood Dynapro big brake hub kit 12.19" diameter vented rotor Wilwood Brake master cylinder and Combination proportioning va
19 1
Roll Cage
Brand new 383 Chev Roller engine Hillborn injection, powerglide. MSD ignition, 35 spline maxispool diff 4.33 diff gears, Harrop alloy diff carrier, deadenbear delaybox, chute, Convo Pro rims, the list goes on. Ground up build, bare metal respray, this car is a true steel body car with everything done and ready for its debut run down the 1/4mile. Receipts for engine and work total well over asking price. Further details contact Chris on 0409348441.
9 1
Roll CageLog Book
Current IHRA tech inspection and logbook. Selling to progress dragster. Tunnel ram Methanol injection on stroker SBC. Motown block, runs a cooling system as well. Racer pro heads and manifold. Trans brake PG transmission and full floater sheet metal 9". Has delay box and solenoid shifter. Turn key car runs super consistent 8.5 sec quarter mile. Enclosed trailer available separately. Can separate and sell as a roller, minus engine and transmission for $12K Or car with watertight enclosed tandem
6
Log Book
FOR SALE 2010 HOLDEN VE COMMODORE UTE SSV SET UP FOR STREET – TRACK CAR – DRAG RACE STREET REGISTERED WITH MOD PLATES QLD REGO 5-24 24500KM ENGINE 6.0 LITRE 495KW ON BACK WHEELS 1180 N.MT FORGE PISTONS ROD BOLTS CUSTOM CAM DOUBLE VALUE SPRING HARROP AIR INTAKE E85 INJECTORS E85 PUMP AND SURGE TANK 2300 HARROP SUPER CHARGER MANUAL 6 SPEED GTS S1 SEQUENTIAL SHIFTER CERAMIC CLUTCH WITH CUSTOM SLAVE CYLINDER 1000HP DRIVE SHAFT WITH 9” YOKE TRU TRACK DIFF CENTRE 4.11 GEARS 1000HP DRIVE SHAFT AXL
10
Statutory write off and fully repaired, We have photos of the damage which was the rear of the car,all receipts are available as well. Being a stat write off this vehicle can not be registered in Australia, can be used for track or export outside Australia. it is priced below our cost and needs to GO.
26
2012 Holden ve track ute cannot be registered. 5.7 LS1 vcm7 cam, ported heads, OTR cold air, trunuin upgrade, buckets, oil pump, timing chain, push rods, springs gaskets were all upgraded at same time was done about 1.5 year ago at KTMR performance. twin into single 3.5 exhaust sounds tuff,all braided oil lines, catch can, oil cooler, oil accumulator, powersteering cooler, coilovers, diff has a harrop full spool rated to handle 1000hp with 3.7 diff gears custom tailshaft (dount delete and bigg
10
PRICE REDUCED AGAIN! Calibra 117k 2.5 v6 man red this car would make a good hillclimber or trackday car has alcon 4p mono front calipers dba club spec t3 330mm rotors alcon advantage 320mm rear rotors 2p calipers arp wheel studs 5x120pcd eibach coils kyb eurospec shocks poly bushes front&rear 17/7 alloy wheels fed rsr 215/40/17&235/40/17 fed 595 rear. Have 3.2 v6 from 2004 vectra with cat cams pac v/springs arp head bolts new balancer mtec billet flywheel with arp studs crossram intake off 3.0l
5
Roll Cage
VY Commodore Drag Ute. Drop an engine setup, ecu and converter in and go racing. Has Coan built T400, Harrop full spool 1000hp rear end, 3" 2 piece chromoly tailshaft, 7 point chromoly cage, chromoly front end, chromoly v6 k frame (can buy LS mounts to suit), wilwood booster delete master cylinder, full fire suppression system, drag bags in the rear, custom built light mags 4" fronts 10" rears, light weight brake rotors and callipers, fibreglass bonnet and doors, perspex front and rear windscree
9
RegisteredRoll CageLog Book
Hi guys here is my 1997 excel gravel car The vehicle itself has one numerous classes and events very capable car in the right hands 1.5liter dohc motor with forged rods and pistons has had extensive head work even down to custom manifold. Wolf ecu MCA fronts with canisters serviced one event ago MCA rears non canistered serviced one event ago Gearbox has just been rebuilt and has a grippa diff and has a new 5 puck button clutch by direct clutches Velo apex seats 6 point velo harnesses 6 p
9
Location Tassie. Fresh, excellent, reliable Irving head motor. Logbooked. Extensive cage, HR seats, current SI Rego. Recent bare metal respray..No expense spared. Well sorted over many years of development. Fast. Extremely competitive Historic hillclimb or circuit capable. Sadly offered as I am hanging up my helmet. Genuine enquiries only please.