34 items for sale

VU SS race/exhibition car project. Sold as rolling concern. Vehicle has a clean title and could be engineered and re registered with some work. Quick rundown *2001 VU SS *Statesman international front end conversion *4 inch reverse cowl *HSV Hard lid *HSV Sail Plain *New Blackout projector headlights *New Blackout Tail lights with LED *New Side Markers *Wilwood brake master *Wilwood brake bias valve *B&M line lock *Electric Power steering Conversion (fully functional for moving the car aroun

FOR SALE 2010 HOLDEN VE COMMODORE UTE SSV SET UP FOR STREET – TRACK CAR – DRAG RACE STREET REGISTERED WITH MOD PLATES QLD REGO 5-24 24500KM ENGINE 6.0 LITRE 495KW ON BACK WHEELS 1180 N.MT FORGE PISTONS ROD BOLTS CUSTOM CAM DOUBLE VALUE SPRING HARROP AIR INTAKE E85 INJECTORS E85 PUMP AND SURGE TANK 2300 HARROP SUPER CHARGER MANUAL 6 SPEED GTS S1 SEQUENTIAL SHIFTER CERAMIC CLUTCH WITH CUSTOM SLAVE CYLINDER 1000HP DRIVE SHAFT WITH 9” YOKE TRU TRACK DIFF CENTRE 4.11 GEARS 1000HP DRIVE SHAFT AXL

General: Full chrome moly tube chassis by Chris Alston in California. Glass front, steel doors and rear. New Tailgate, body stripped and repainted in custom pearl blue. Custom wing, wheelie bars, parachute. 20l alloy fuel cell, new rear mounted battery. Linelock and quick release steering wheel, 5 point harness, alloy ice box. Completely rewired throughout. Certified by both NZDRA and IHRA. All fabrication done by Raceworks in 2021. Engine: 427 LS7 built by Steve Morris in USA in 2021, approx 10

Statutory write off and fully repaired, We have photos of the damage which was the rear of the car,all receipts are available as well. Being a stat write off this vehicle can not be registered in Australia, can be used for track or export outside Australia. it is priced below our cost and needs to GO.

2012 Holden ve track ute cannot be registered. 5.7 LS1 vcm7 cam, ported heads, OTR cold air, trunuin upgrade, buckets, oil pump, timing chain, push rods, springs gaskets were all upgraded at same time was done about 1.5 year ago at KTMR performance. twin into single 3.5 exhaust sounds tuff,all braided oil lines, catch can, oil cooler, oil accumulator, powersteering cooler, coilovers, diff has a harrop full spool rated to handle 1000hp with 3.7 diff gears custom tailshaft (dount delete and bigg

VS SPAC LS1 AUTO. $25,000 Freshly finished and converted LS1 auto 4l60e. Top end rebuild on the engine, cam, heads shaved and rebuilt, new double row timing chain, oil pump, lifters and springs. New Manifold, radiator, rebuilt auto, 3000 dominator stall, new front and rear brakes and front shocks, new steering rack and new tailshaft. Brand new rod shop conversion kit and new exhaust. New fuel reg, lines and fittings. New in tank walbro pump, new manifold. New mini low mount A/C pump installed

PRICE REDUCED AGAIN! Calibra 117k 2.5 v6 man red this car would make a good hillclimber or trackday car has alcon 4p mono front calipers dba club spec t3 330mm rotors alcon advantage 320mm rear rotors 2p calipers arp wheel studs 5x120pcd eibach coils kyb eurospec shocks poly bushes front&rear 17/7 alloy wheels fed rsr 215/40/17&235/40/17 fed 595 rear. Have 3.2 v6 from 2004 vectra with cat cams pac v/springs arp head bolts new balancer mtec billet flywheel with arp studs crossram intake off 3.0l

Unfinished project. Extensive chassis mods, 3/4 chassis kit, Watts link rear suspension, brand new Braced 9" diff, 3.9 gears and Detroit locker with 35 spline full floating axles strange nodular iron carrier. PBR M series brakes (vt-vz) 6 piston fronts and 4 piston rears, all 4 rotors are 2 piece design and 360mm. Tilton 9000 series brake pedal set Tremec 5 speed TKO box triple plate clutch 7&1/4 inch clutch 19" 3 piece simmons wheels FR19s 8" front 10"rear Coil over front end conversion Flaming

2000 vt v6 wanting to sell, for someone to use as a drag racing car, engine is still good, seats need to get change over, car windscreen got damaged by someone who vandalised it, and front passager window is broken, hence why I'm selling it to anyone needing a good car to modify for drag racing or doing donuts on the track. Unlicensed.

1967 HB Torana Roller for sale Complete roller ready for paint, selling minus the wheels. Built by Matt Marsh @ PSI in Wollongong over $60k in fab/body work, full perspex windows, 4 link 9” inch, tubbed, wheely bars, parachute and strange disc brakes. Diff Center is a Lenco aluminium 35 spline full spool All original tags, engine mounting plate to suit small block, box mounts setup for power glide. Fibreglass bonnet, boot and bumpers