100 items for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
10
Lotus 7/ Clubman chassis. This car was raced by my father in the 70s and has been in storage since. Believed to be a Lotus 7 but cannot verify this, the only stamp I can find on the chassis is shown in the photos. Definitely not complete but includes many parts as pictured. Happy to answer any questions or arrange more photos if required.
3
AP Racing CP6465-218 pull type master cylinder 21.8mm
4
3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17 NOTE WHEEL ARE FOR VR VS COMMODORE
3
Sydney Composites front splitter, used at WTAC in 2023 would suit either open class or Pro-Am, 2200mm wide and 810mm wide but can be reduced if required. Proven to produce massive down force with low drag. Titanium Wear Plates. Only selling due to changing direction. Happy to answer questions 0427700423 and can freight Austria wide
2
Near New M800 and Data Logger Dash has not been used I owned as a spare for my FD RX7 Racecar. features enabled are as follows: M800 SN1323 single lambda, Hi/lo injection, Cam control, Advance functions (Traction control, Launch Control, Gear Ign cut, Overun boost) Dash ADL Dash SN 2732 shift / warning lights 1mb logging, Pro logging, standard inputs, See attached screen shot
3 1
This is a engine I got from purchasing a chassis i was after, so all parts are for sale. This auction is for a 600hp 873Nm touque @ 5500rpm, turn key engine eveything from coils, headers, drysump set up. It has alloy 23 degree heads, 180 degree headers. JE Pistons Scat 4340 crank Manley I beam conrods Brodix 23 degree alloy heads Comp cam roller camshaft Demon carburetor Crane ignition, with Crane ignition coil, MSD Distributor, MSD Leads, Custom MRX steped headers F1 merge collector's Runs o
2
This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.
5
Xtrac Sequential 6 speed. BMW M54 bellhousing and drive output, with E46 crossmember. New flywheel and release bearing. Pneumatic or lever shifted. Lever included (No paddles included)
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
4
350 Fuel Injected Chev Engine, built as a project, only dyno time. Never installed to a car. 600BHP @7000. Autronic ECU & Harness, Miloden wet sump . SHP Dart 4 Bolt Block. Crower Crank. New parts include, NC'd Brodix Heads (1188106), stainless valves, Jessel Shaft Rockers, Brodix manifold (HV1814), CP Pistons & pins, Oliver 6" Rods, Isky roller cam 294: 302: 108. MSD dual Ignition 9:1 Comp ratio, tuned & mapped on 98 unleaded fuel. Very smooth & progressive. Ready to install. Ideal f
6
ADL2 Motec Dash Good Working Condition Supplied with new harness and connector as supplied by Motec QLD Also supplied with pinout sheet Brisbane
2
Brand new still in box as it arrived from the US WYO Billet Lock Up Unit Includes Trans Dump Valves for air shifting gearbox Was planned to work with a 5 speed Liberty Cost $24,000 to land here from the US and they are more now Save $4,000 and 6 months wait!!
3
New Wiseco pistons New bearings Carrillo rods Internally balanced crank Solid roller Crow cam reground Crane roller lifters Aluminium Yates Roush C3 heads Titanium inlets, stainless exhaust valves T & D shaft mounted rockers, as new Ford Motorsport High Rise Manifold Fully studded heads and main caps Isky springs High volume oil pump High volume water pump
4
Getrag M51 5 speed Volvo Dogleg 1st 1:1 5th 1st - 3.99:1 2nd - 2.58:1 3rd - 1.77:1 4th - 1.27:1 5th - 1.00:1 10x 29mm input spline Has speedo output to suit rally car Output Flange to suit Group A spec cars Sierra Volvo Mercedes etc Never been in a race car and in excellent condition Located on Gold Coast, Freight opitions available
8
1244 CC Reground 113E Ford crankshaft, reinforced centre main bearing cap. Repco solid skirt pistons on 113E conrods, Tri Metal main and rod bearings , Grant Rings . 10:1 compression, Holbay 658 full race camshaft, duplex chain drive. Head fitted with stainless oversize valves 7mm stems in Bronze guides , hardened valve seat inserts, PSI competition springs, custom spring seats and retainers, Titan roller rockers, ford cam followers and pushrods new SPR rocker cover. New uprated Capri oil pu
4
Hussla gloss black 19 x 8.5 front rims and 19 x 9.5 rear rims to fit commodore will not fit large brembo brake applications the frons are brand new the rear were only on the car for 3 weeks they are like new Cash only pick up only
3
MSD 7720,7730,,harness, coil all new Boxed
3
Haltech 950 with complete harness New in box